Using 3M™ Retraction Capsule, 3M™ Intra-oral Syringes, 3M™ Impression Trays and 3M™ Imprint™ 4 Penta™ Heavy and Imprint™ 4 Light VPS Impression Material
Making an acceptable impression in dentistry requires not only the use of precision impression material but also the use of adjunct materials to help support the accuracy of the final impression. 3M introduced a line of products that are intended to be used together to maximize the efficiency of taking an impression while offering predictability to the clinician.
Learn more about the products used in this clinical case |
An 80-year-old male presented with a fractured and decalcified upper right canine (tooth #6). After reviewing clinical and radiographic findings it was determined that a full porcelain crown was the best treatment of choice.
Initial impressions were obtained including a template for temporary fabrication, a study model and an opposing full arch mandibular impression (using 3M impression tray). After placing local anesthetic, the tooth was prepped for a full porcelain crown.
Prepared tooth #6
Prior to the final impression, 3M retraction capsule (3M) paste was injected into the sulcus of tooth #6.
3M™ retraction paste in place around preparation
The retraction paste contains 15% aluminum chloride and is intended to provide temporary tissue retraction and enable a clean, dry and controlled sulcus. 3M retraction capsule paste material can be used alone or in conjunction with retraction cord. The soft and narrow tip of the 3M retraction capsule corresponds in size and shape to a periodontal probe; designed for direct placement in the sulcus.
3M™ Retraction Capsule and periodontal probe tips are similar in size
While the retraction paste is in place, a 3M impression tray is fitted. The trays come in three sizes and require no adhesive. The self-retentive strips are designed to direct the flow of the impression material, minimizing defects and voids.
3M™ Impression Tray
The 3M intra-oral syringe is loaded with the appropriate amount of Imprint™ 4 Light.
3M™ Intra-oral Syringe connects easily to a cartridge
The syringes are single use, ergonomically designed, and can be prepared in advance. The syringe is designed for the loading of consistent amounts of wash for both single and multiple preps. There are markings and characteristics on the syringe that will accommodate specific amounts.
3M™ Imprint ™4 Light is placed from the 3M™ Garant™ Dispenser into a 3M Intraoral Syringe, and the tip can be directed for precise application.
Using the syringe is much easier than trying to guide the 3M™ Garant™ cartridge with extended mixing tips. The 3M intra-oral syringe uses less material and allows more accurate placement.
Once the Retraction Capsule material is placed, simply rinse the material at the time limit making sure no residue remains in the sulcus. Next, Imprint 4 material is extruded from a Pentamix mixing unit into a 3M impression tray.
Loading 3M™ Imprint ™4 material into the 3M™ Impression Tray using a 3M ™ Pentamix™ 3 Automatic Mixing Unit
Since the 3M intra-oral syringes can be prepared in advance, the material can be syringed around the prep while the tray is being loaded. The tray is gently placed and allowed to set. Imprint 4 Light (regular set material) has a maximum 1:00 minute intra-oral syringing time at room temperature. Intra-oral set time for Imprint 4 regular set material is 2:00 minutes.
Full-arch final impression
When the impression is set, remove it and check for blue residue and excess pieces of impression ‘flash’. These may be on teeth or soft tissue. The final impression (Figures 9-10) shows excellent marginal detail. The color contrast is easy to read, crisp and accurate, with no delamination.
Worth noting: In addition to providing a precise impression medium, Imprint 4 material (3M) has an active self-warming feature that accelerates the intraoral setting time. The setting time starts after placement and speeds up with body temperature.
Detail of impression
A temporary crown is fabricated using the pre-prep impression template. The Imprint 4 impression and models were sent to the lab where an all porcelain crown was fabricated.
Temporary crown
The patient returned 10 days after the prep work for delivery of the restoration. No complications or problems occurred during temporization. The restoration was tried in, adjusted and bonded into place.
The patient is comfortable and pleased with the final result.
Final restoration
The 3M products used in this restorative process helped create a beautiful restoration. The materials and delivery system are excellent. These products are designed to be used sequentially and gives the clinician confidence in accuracy of both impression and final restoration
Refer to Instructions for Use (IFU) for complete product information. Results may vary.
Using 3M™ Single Bond Universal Adhesive, 3M™ Filtek™ Supreme Flowable Restorative, 3M™ Filtek™ Universal Restorative, 3M™ Elipar™ Deep Cure-S LED…
Using 3M™ Scotchbond™ Universal Adhesive, 3M™ Filtek™ One Bulk Fill Restorative, and the 3M™ Sof-Lex™ Spiral Finishing and Polishing system.
Using 3M™ Protemp™ 4 Temporization Material, 3M™ Scotchbond™ Universal Plus Adhesive, and 3M™ RelyX™ Universal Resin Cement.
